Jeep43's Recent Activity

  1. Jeep43 attached a file to the thread 74 Z28 Build - Stock appearing performer.

    I shot the repair with epoxy primer and then finished up with "Autozone body and paint" aka single stage aerosols. I've always used 2k...

    thumbnail (2).jpg thumbnail (3).jpg thumbnail (1).jpg thumbnail.jpg Feb 22, 2018 at 8:44 AM
  2. Jeep43 posted a new thread.

    Horn resto

    I have what I think is the original horn for my 74. Its kinda crudy with overspray etc. It works. Any tips to clean this up myself?? I...

    DSCF9721.JPG DSCF9720.JPG

    Forum: Electrical Systems

    Feb 21, 2018 at 8:12 PM
  3. Jeep43 replied to the thread One-man brake bleeding technique.

    LOL, I used to call on my wife and then she bought me her replacement (at least for brake bleeding duties) for my birthday....

    Feb 21, 2018 at 10:37 AM
  4. Jeep43 replied to the thread Mystery brake line question....

    The brake line will have the spiral armor on it, the vent line wont.

    Feb 21, 2018 at 10:28 AM
  5. Jeep43 replied to the thread To use a clutch fan or not?.

    I have trouble understanding how a fluid or clutch fan could spin faster than the shaft its attached to..... Perhaps maybe immediately...

    Feb 20, 2018 at 10:58 AM
  6. Jeep43 replied to the thread Pypes SGF70 questions.

    Pypes said EVT-58 Long for my car. I found an open box pair for cheaper on ebay and but the bullet on the SGF-70. I guess I spent enough...

    Feb 20, 2018 at 10:54 AM
  7. Jeep43 replied to the thread Survivor: Keep original or modify the engine/drivetrain?.

    When I think of "survivor" I tend to think of original and presentable body and interior. I would still consider a car that had a major...

    Feb 20, 2018 at 9:09 AM
  8. Jeep43 replied to the thread 2 BOLT VS 4 BOLT MAIN POWER CAPACITY.

    Whats the cost difference between 2 bolt studs and line hone vs install of splayed caps??

    Feb 20, 2018 at 8:54 AM
  9. Jeep43 replied to the thread Need Lower Patch Panel for 72 Camaro Fender.

    Not yet. My car needs the very bottom of the 1/4 both fore and aft of the wheel well. In addition, the part of the 1/4 that forms the...

    Feb 20, 2018 at 8:48 AM
  10. Jeep43 replied to the thread Need Lower Patch Panel for 72 Camaro Fender.

    I ended up being able to salvage enough of the stamped detail to weld to the bottom of my patch. A lot of work but it came out OK. I...

    Feb 19, 2018 at 1:40 PM
  11. Jeep43 replied to the thread 4 speed reverse lights.

    The bracket bolts to the rear shifter stop adjustment bolt on my Hurst Comp Plus. I assume the stock shifter does not have these stop...

    Feb 19, 2018 at 9:43 AM
  12. Jeep43 replied to the thread Cowl drain holes.

    I tried picking bits out but I would be there forever trying to break chunks up. I ended up passing a 3/4 unibit thru there to max it...

    Feb 18, 2018 at 4:53 PM
  13. Jeep43 posted a new thread.

    Cowl drain holes

    [ATTACH] As I was drilling out a snapped lower fender bolt I noticed a blank hole nearby. As I poked inside with a screwdriver tons of...

    DSCF9719.JPG

    Forum: Camaro Questions

    Feb 18, 2018 at 2:19 PM